Construction Chemicals Formulations is a technical formulations reference covering 56 starting-point formulations across 10 categories: cementitious waterproofing (rigid, crystalline, polymer-modified and rapid-plugging); liquid-applied membranes (acrylic, polyurethane, bituminous and polyurea); tile adhesives and cement grouts; self-leveling underlayments, screeds and floor hardeners; repair mortars, micro-concretes and bonding slurries; grouts, anchors and injection resins; wall putties, plasters, renders and ETICS; concrete and masonry protection; curing, release and retarding aids; and selected sealant and epoxy systems for construction use. It is written for manufacturers, applicator and contractor brands, and R&D chemists, and it does not cover concrete admixtures.
The book builds each product family from its binder chemistry: Portland cement hydration to calcium silicate hydrate and portlandite, and the pozzolanic and silicate reactions used for pore blocking; ternary Portland, calcium aluminate and calcium sulfate binders for rapid set and shrinkage compensation, with lithium and citrate set control; polymer-modified systems based on redispersible vinyl acetate–ethylene powders and cement-stable acrylic dispersions that form polymer–cement co-matrices; moisture-cure and two-component polyurethane and polyurea isocyanate chemistry, including prepolymer synthesis and NCO index; silane and silicate pore treatments; and radical-cure methacrylate anchors. Each category gives raw materials by INCI or IUPAC name, additive classes, specifications and grade structure, a manufacturing sequence for dry-mix and liquid lines, packaging and storage, failure modes, product-range architecture and regulatory notes.
All 56 formulations are structured across Economy, Mid-range, Premium and Specialist builds. Each block gives an INCI or IUPAC-named component table in % w/w with the mechanism of action and sourcing tier of every component, a condensed method with scale-up notes, QC targets with the named test method, an HSE line, stability notes, variants and the scientific basis. Two-component products show Part A and Part B with the mix ratio, and isocyanate systems state the NCO index.
Construction chemical products rise or fall on a few controls: water and polymer dosing in dry-mix powders, binder cleanliness, shrinkage control and bond to the substrate. This handbook gives 56 starting-point formulations across ten product categories, each with the manufacturing controls, QC targets and failure-mode diagnosis behind it.
You make or plan to make dry-mix mortars, waterproofing, tile-fixing or repair products and want formulation starting points with named raw materials, treat rates, dry-blend and liquid-blend process steps, and QC targets tied to EN and ASTM test methods.
You apply or private-label waterproofing, flooring and concrete repair systems and want the chemistry behind what you specify: crystalline and polymer-modified slurries, liquid membranes, R1–R4 repair mortars, injection resins and anchors, so you can select systems and diagnose site failures.
You run a laboratory or are entering the construction chemicals segment and need a structured reference: product tiers from economy to specialist, commodity versus specialty sourcing, plant requirements, packaging and shelf life, and the regulatory points (CE marking routes, chromium(VI) in cement, respirable silica, diisocyanate training) that shape a range.
They are validated starting points. You will need to bench-test and adapt treat rates to your specific raw material lots, but you start from a working formulation — not a blank sheet.
The handbook is a PDF — high-resolution A4, printable, with bookmarks and a linked table of contents. You receive an instant download link and it is also available in your library indefinitely.
Up to 5 downloads are included with your purchase. If you need more, contact us and we will reset your download limit.
Yes. The handbook opens with a fundamentals section that explains the underlying chemistry and ingredient functions before presenting formulations — so beginners can follow the rationale, not just the recipe.
No. Concrete admixtures (plasticizers, superplasticizers, set-control and air-entraining admixtures) are not covered in this volume. It covers dry-mix mortars, waterproofing, tile fixing, flooring, repair and grouting, wall finishes, protection treatments and construction aids.
Dry-mix products are written as % w/w of the dry blend, summing to 100%, with the mixing-water ratio in the method note. Two-component products give Part A and Part B separately with the mix ratio, and isocyanate systems state the NCO index. Mixing-water ratios and set-sensitive additives, such as lithium carbonate and citric acid in calcium aluminate systems, are marked for confirmation by pilot trial.
The EN 1504 series, EN 14891, EN 12004 and ISO 13007, EN 13813, EN 998-1, EN 13279-1 and EN 15824, ASTM C109, C309, C836, C928, C1107, C1305 and D6083, and Indian Standards IS 269 and IS 15477, among others. Class limits and clauses are marked for confirmation against the current edition. The book gives reference anchors, not approvals, and label claims need certified testing and supplier letters.
Yes, in construction use. Categories 02 and 06 cover polyurethane and polyurea membranes, polyurethane injection resins and methacrylate chemical anchors. Category 10 adapts selected sealant and epoxy primer and injection systems from the Adhesives & Sealants and Epoxy Coatings volumes for use alongside the cementitious products.
A component table in % w/w with the function (mechanism of action) and sourcing tier of every component, a condensed method with scale-up notes, QC targets with the named test method, an HSE line, stability notes, variants and modifications, and the scientific basis. Each category also gives raw materials, additive classes, grade structure, manufacturing sequence, packaging and storage, failure modes, product-range architecture and regulatory notes.