Process Safety

Process Safety Consultant: When to Hire One and Why

Process safety consultant hire — pilot plant bay with a stainless steel reactor vessel, agitator drive and insulated pipe line | Global Formulation
A pilot-scale reactor with an agitator drive and an insulated line leaving the vessel: scale-up is one of the clearest triggers for outside process safety support.

An owner usually looks for a process safety consultant after a trigger: a new process, a scale-up, a plant change, an incident or a regulator's question. A process safety consultant is an outside specialist who helps an owner identify, evaluate and control process hazards, usually by leading hazard studies and preparing the records a regulator expects. This guide sets out when that help is worth buying, what to ask for and how to judge the people offering it. It draws on rules of the US Occupational Safety and Health Administration (OSHA) and Environmental Protection Agency (EPA). It also uses guidance from the Health and Safety Executive (HSE) in Great Britain and from the Center for Chemical Process Safety (CCPS). The scope matches the HAZOP and HAZID studies and thermal hazard assessment that Global Formulation supports for plant owners.

What a Process Safety Consultant Does and What Stays with the Owner

A consultant supplies what the owner's team lacks: method knowledge, measured data, independence or spare capacity. The legal duty does not move. In the United States, the OSHA process safety management (PSM) standard, 29 CFR 1910.119, places each duty on “the employer”. The EPA Risk Management Program (RMP) rule in 40 CFR Part 68 places the same duties on “the owner or operator”.

Under OSHA's text, outside help is a choice. The standard requires at least one employee with process experience on the analysis team. For the method and the audit it asks only for knowledge, not employment. The table sets out each duty, the rule text read for this guide (the eCFR text current at 29 October 2026) and the place where a consultant fits.

DutyWhat the US rule text saysWhere a consultant fits
Process hazard analysisOSHA 1910.119(e): a team with engineering and process operations expertise, including an employee who knows the process and a member who knows the methodLeads the method, records the worksheets and tracks the actions, while plant staff supply the process knowledge
Employee participationOSHA 1910.119(c): the employer consults employees and their representatives on the conduct of process hazard analysesPlans the sessions so that operators and maintenance staff can attend
Management of changeOSHA 1910.119(l): written procedures must address the technical basis of a change and its impact on safety and health before the changeReviews the technical basis and the hazard data behind a proposed change
Pre-startup safety reviewOSHA 1910.119(i): before hazardous chemicals are introduced, confirms construction matches design, procedures are adequate, a new facility's analysis recommendations are resolved and training is completeChecks each item against the as-built plant and the action register
Incident investigationOSHA 1910.119(m): starts within 48 hours, with a team that includes at least one person knowledgeable in the processAdds investigation method and analysis beside the plant staff who know the process
Compliance auditOSHA 1910.119(o): the employer certifies an evaluation at least every three years, conducted by at least one person knowledgeable in the processConducts or leads the audit; EPA requires a third party in set cases, covered below

In this guide, a process safety consultant is an outside specialist engaged for a defined scope. A process safety engineer on the payroll is the in-house alternative and appears in the comparison below. The word consultant also covers a facilitator hired for one study, so the scope has to be written down.

Other jurisdictions

Other regimes assign duties differently. In Great Britain the Control of Major Accident Hazards Regulations 2015 (COMAH) apply. HSE's inspection guidance asks whether staff and contractors are only given work for which they are competent. The European Union's Seveso III Directive (2012/18/EU) and India's Manufacture, Storage and Import of Hazardous Chemical Rules, 1989 are named here without clause detail.

India's rules, as notified in 1989, require an occupier to prepare a safety report for covered industrial activity, and later amendments were not reviewed. Confirm the regime for the site before relying on a United States description.

When to Hire a Process Safety Consultant: Six Triggers

This section lists six situations in which an owner has a clear reason to bring in outside process safety help. Each has a rule hook in the United States and a plant consequence if the work is skipped. The table gives the trigger, why an outside specialist helps and what to ask for first. A scoped study is a safer first purchase than an open-ended retainer, because its deliverables can be checked.

TriggerWhy outside help fitsAsk for firstUS rule hook
A new process or plant at concept or design stageHazards are cheapest to remove before they are drawnAn early hazard study and a list of the studies the project needsOSHA 1910.119(e) and (i): analysis performed and resolved before start-up of a new facility
A scale-up from laboratory or pilotHeat removal per unit volume falls as vessels grow, so a reaction that is easy to control in the laboratory can exceed plant coolingMeasured heat-release and decomposition data, then a hazard study on the plant designOSHA 1910.119(d): process safety information includes thermal and chemical stability data
A change to an existing process, product or capacityChange control decides how much to re-examine, and the technical basis needs an independent checkA review of the proposed change against the current process safety informationOSHA 1910.119(l): management of change
An incident or a near missThe investigation must start quickly and needs a method as well as process knowledgeInvestigation support working beside the plant staff who know the processOSHA 1910.119(m); EPA 40 CFR 68.81, with root cause by a recognized method for incidents meeting the accident-history criteria
A review date: revalidation every five years or an audit every threeThe analysis must match the current process, and an audit gains from fresh eyesA scope that names which studies and audits fall due, and whenOSHA 1910.119(e)(6) and (o); EPA 40 CFR 68.79
A gap: no method-trained leader, no spare team time or a need for independenceThe team needs one member who knows the method, and independence from the design is the better practice for the leaderA facilitator whose independence from the design is stated in writingOSHA 1910.119(e)(4)

The first two triggers come before the plant is built, which is when change is easiest. A hazard found at concept stage needs a drawing change, while the same hazard found after construction needs changes to built plant. For a scale-up, our guides to reaction calorimetry and to adiabatic temperature rise and MTSR explain the data a hazard study needs. Our scale-up support page covers the move from laboratory to plant, where the process meets equipment nobody has yet operated.

Process safety consultant data scope — bench-top glass reaction vessel with dropping funnel, clamp stand and hoses to a stainless circulating bath | Global Formulation
Bench-scale glassware with a dropping funnel and a circulating bath: laboratory work of this kind is the starting point for the thermal data a hazard study needs.

When in-house is enough

An owner with a method-trained leader, current drawings and measured data can run a study without outside help. The test is whether the team can show all three to a regulator, an insurer or a lender. If any one is missing, that gap is the reason to hire. Hiring for a gap that does not exist adds cost without adding evidence.

Process Safety Management Consultants and Process Hazard Analysis Consultants: Scope of Work

The two job titles describe different scopes, and quotations are only comparable when the scope is written down. In this guide, process hazard analysis consultants lead the hazard studies, as a HAZOP facilitator does. Process safety management consultants work across the programme elements of the PSM standard, such as management of change, audits and procedures. Many engagements mix both, and the brief should say which is meant.

The table lists the engagements an owner can buy, what is delivered and what the owner must supply. The owner's inputs decide how long the work takes, so they belong in the quotation request. Our guide to the HAZOP study covers the most common study in detail.

EngagementWhat the owner receivesWhat the owner must supply
Hazard study facilitation (HAZOP, HAZID, what-if)Worksheets, a team record and an action registerA frozen drawing revision, the process safety information and team members released for the sessions
Thermal hazard assessmentHeat-release, accumulation and decomposition data, with a runaway assessmentThe process recipe, samples and the dosing profile
LOPA and SIL reviewA scenario-by-scenario check of whether independent safeguards are enoughScenarios from the hazard study and data on the safeguards
Relief and venting designRelief scenarios, a sizing basis and a discharge routeVessel design pressures, worst credible scenarios and any test data
Hazardous area classificationClassification drawings and an equipment selection basisMaterial properties, release sources and ventilation data
Pre-startup safety reviewA verified checklist and a record of the actions closedAs-built drawings, procedures and training records
Compliance auditAn audit report with findingsAccess to records and staff, and a plan to respond to the findings

LOPA is layer of protection analysis, and SIL is safety integrity level. The process-sector standard for instrumented safety functions is IEC 61511-1, Edition 2.1 (2016 with Amendment 1, 2017), published by the International Electrotechnical Commission (IEC). This guide names it only and gives no level or set point, since both depend on the plant. A hazard study lists the scenarios and does not supply heat-release data, relief sizing or integrity levels, so the brief must ask for each separately.

Process safety consultant review scene — insulated discharge line to a bunded outlet beside a guyed vent stack with an access ladder at dusk | Global Formulation
An insulated discharge line routed to a bunded outlet beside a guyed vent stack: where a discharge goes is one of the points a pre-startup review checks against the design.

The earlier-stage study is covered in our guide to preliminary vs process hazard analysis, which settles what a contract means by the abbreviation PHA. That distinction matters before any quotation is accepted.

In-House Team, Outside Facilitator or Independent Reviewer: Which Model Fits

Four delivery models cover the choices an owner has when engaging process safety consultants. They are the in-house team, an outside facilitator, a full-scope consultant and an independent third-party reviewer. Figure 1 shows the questions that point to each. The table compares them on four criteria rather than on adjectives.

Illustrative questions that point to the type of outside process safety help Four question boxes run down the left side, each linked by a downward arrow. The first asks whether the team includes a member who knows the study method, and a no answer points to an outside facilitator or a method-trained leader. The second asks whether measured thermal and chemical data is in hand, and a no answer points to a thermal hazard assessment before the study. The third asks whether the review must be independent of the design or the site, and a yes answer points to an independent facilitator or a third-party reviewer. The fourth asks whether named plant staff can be released for the sessions, and a no answer means the analysis team cannot be seated, so the study is rescheduled. The figure is a generic illustration. Does the team include a member whoknows the study method? No: add an outside facilitator ora method-trained leader no Is measured thermal and chemicaldata in hand? No: commission a thermal hazardassessment before the study no Must the review be independent ofthe design or the site? Yes: use an independent facilitatoror a third-party reviewer yes Can named plant staff be releasedfor the sessions? No: the analysis team cannot beseated; reschedule the study no yes yes no Illustrative aid for scoping a hazard study; it is not a rule from any regulation.
Figure 1. Illustrative questions that point to the type of outside help. It is a generic aid, not a rule from any regulation.
CriterionIn-house teamOutside facilitatorFull-scope consultantIndependent third-party reviewer
Independence from the designLow where the team designed or runs the plantHigh, if the facilitator had no role in the designDepends on whether the same firm designed or supplied equipmentHighest, and fixed by the contract
Method skillPresent only if someone is trained in the methodThe reason for the hireFacilitation plus calculation and testingAuditing technique
Plant knowledgeHighestDepends on the briefing and the teamBuilds up during the engagementDepends on access to records and staff
Measured dataOnly if the plant or laboratory can produce itNot suppliedSupplied or commissionedNot supplied

The models combine. An owner can run studies in-house with an outside facilitator and add an independent audit at the review date. In every model the owner keeps the record and closes the actions, because paragraphs (e)(5) and (e)(7) of the OSHA standard place both on the employer.

How to Judge a Process Safety Consultant: Competence and Independence

A process safety consultant is judged on what the named people have done, not on the firm's brochure. HSE's guidance for inspecting competence at COMAH sites says that formal training alone does not make a person fully competent, because competent also includes adequate experience. Two things need checking: competence for the process in question, and independence from the design and the outcome. The sources below give a benchmark for each.

The same HSE guidance, titled Core topic 1: Competence assurance, asks whether staff and contractors are only given work for which they are competent or are supervised while learning. The question names contractors as well as staff. An owner can use it as a test for any outside specialist, wherever the site is.

Credentials: what they show

A credential shows what its issuer tested, and no more. The CCPS Process Safety Professional Certification (CCPSC) is one example. The page on the American Institute of Chemical Engineers (AIChE) site states that it is not a training program and that it verifies competency in process safety tools and techniques.

Eligibility asks for a science, engineering, mathematics or technology degree and more than five years of post-degree experience. Without such a degree the page asks for ten years. The experience must be broad enough to make the applicant familiar with the 20 elements of Risk Based Process Safety.

The review covers education, experience and three references, followed by an online open-book examination that must be completed within four hours. Holders renew annually, and the renewal includes a continuing education requirement. Nothing on the page says a holder has experience of a given process type. Other countries have their own credentials, so ask what each one tests and how it is kept current.

Independence: a written benchmark

The clearest open text on competence and independence for an outside party is in EPA's third-party audit rule. Section 68.80(c) of 40 CFR Part 68 lists criteria the owner must determine and document for a third-party auditor. They apply to RMP compliance audits, not to hazard studies. They still make a usable benchmark for any outside reviewer, and the list below paraphrases them.

  • Knowledge — familiarity with the requirements of the rule being audited.
  • Experience — experience of the type of source and processes audited, and of the applicable recognized and generally accepted good engineering practices.
  • Technique — training or certification in proper auditing techniques.
  • Impartiality — acting impartially and receiving no financial benefit from the outcome apart from payment for the service.
  • Conflicts — a signed and dated conflict of interest statement from every third-party participant.
  • Cooling-off — no employment with the owner for at least two years after the final report, with audit work excluded.
  • Policies — written policies and procedures that make personnel comply with the criteria above.

Under section 68.79(f), the next audit must be a third-party audit after an accidental release that meets the criteria of section 68.42(a). It must also be one when an implementing agency requires it, or when a previous third-party audit failed the competency or independence criteria. These provisions are in the eCFR text current at 29 October 2026, and they are under review. EPA's proposal of 24 February 2026, published at 91 Federal Register 8970, offers two options. One rescinds the 2024 third-party audit provisions, and the other narrows them to facilities with two accidents in a five-year period. EPA's page for the proposal showed no final rule when checked, so confirm the current text before relying on it.

Questions to put to a candidate

The questions below turn the benchmarks into a conversation. Ask for the answers in writing, since a written answer can be checked later. Ask every candidate the same questions so that the answers can be compared. A vague answer to any of them is a finding in itself.

  1. People — who, by name, will lead each session, and which studies on similar processes have they led?
  2. Method — which method will be used, and can we see its description and a sample worksheet?
  3. Independence — what role did the facilitator or the firm have in the design, the equipment supply or the outcome?
  4. Data — where will measured thermal and chemical data come from, and who is accountable for it?
  5. Inputs — what must our team supply, and for how many people and days?
  6. Modes — how will start-up, shutdown and maintenance be treated?
  7. Actions — how will recommendations be recorded, assigned and tracked to closure?
  8. Sources — which rules and standards will the report cite, with their edition and jurisdiction?

What Goes Wrong When a Process Safety Consultant Is Hired Badly

Hiring goes wrong in a few recognisable ways, and each leaves a plant consequence that appears after the money is spent. The table lists eight of them with the step that prevents each. Most trace back to the brief and the preparation, which the owner controls. The checklist in the next section closes them.

What goes wrongConsequenceHow to prevent it
The brief says only “PHA consultant”Each bidder prices a different study, and the missing one is found lateName the study, the rule and the deliverable in the scope document
The plant's team is not released for the sessionsThe analysis lacks an employee who knows the process, so it does not meet the team requirementBook named operations and maintenance staff before the sessions are scheduled
The designer also facilitates the review of the designAssumptions made in design go unchallenged, so real hazards stay unexaminedState the facilitator's independence from the design in writing
The study runs on outdated drawingsThe team studies a plant that does not existCompile the process safety information and freeze a verified drawing revision first
Thermal data is assumed, not measuredA runaway is named as a consequence, but its speed and size are unknownCommission the measurements before the study and cite them in the report
Recommendations have no owner or dateThe same findings return at revalidation, and the record fails an auditKeep an action register with an owner, a date and a closure note for each item
A general credential is read as sector experienceThe leader can meet the process for the first time in the sessionAsk for named leaders and their experience of similar processes
The consultant is expected to carry the legal dutyThe duty stays with the employer, so unresolved findings remain the owner'sAssign a named person on the owner's side to receive, resolve and close every finding

The first three rows are prevented by a clear brief written before any quotation is requested. The rest are prevented by preparation and follow-through. A study built on the wrong drawing or the wrong chemistry produces confident worksheets about a plant that does not behave that way.

Hiring a Process Safety Consultant: An Owner's Checklist

An owner who briefs the work precisely gets a deliverable that can be checked against a rule. The brief is short, and each line closes a question that would otherwise surface in the middle of the project. Work through the eight items below before inviting quotations. The list applies to a single study or to a wider engagement.

  1. Name the trigger — new process, scale-up, change, incident, review date or capability gap, so that bidders price the same need.
  2. Name the study or service — write the hazard study, thermal assessment, audit or review in full, with the rule or contract clause behind it.
  3. Confirm the regime — state the jurisdiction and, in the United States, whether OSHA 1910.119 or an EPA RMP program applies.
  4. Fix the inputs — the drawing revision, the process safety information and the measured data the owner will supply.
  5. Seat the team — named plant staff for each session, released from their duties.
  6. Set the independence rule — what role the consultant did or did not have in the design or supply.
  7. Agree the outputs — the report contents, the action register format and who owns closure.
  8. Plan the follow-through — a closure review before start-up, retention of the record and the next review date.

On delivery the owner should receive the following:

  • a statement of the scope performed and the requirement it answers;
  • a team record with names, roles and attendance;
  • the worksheets, calculations or audit findings;
  • an action register with an owner, a due date and a closure status for each item;
  • the study basis, including the drawing revisions and the data sources;
  • the date on which the work next falls due.

To check the work, compare the drawing revisions in the report with those issued, and confirm that the report names the rule or standard with its edition. Then sample a handful of actions at random and confirm that each has an owner, a date and a status.

What drives the fee

Fees follow scope, so this guide gives no figure. Quotations are comparable only when the same drivers are stated in the request. The drivers below are the ones to put in it. A bidder who asks about none of them has not read the brief.

  • the number of drawings or study nodes, and the complexity of the chemistry;
  • the number of session days and the size of the team;
  • the condition of the drawings and process safety information;
  • the amount of measured data that must be produced;
  • the depth of the report and of the action tracking;
  • travel, and the schedule of revalidations or audits.
Competent-assessment statement Whether a plant needs outside help, which study it needs and who is competent to lead it depend on the site, the chemistry, the design stage and the regime that applies. The work has to be led by a qualified process safety professional and judged against the regulatory regime for the site. This guide explains when and why owners hire a process safety consultant so that an owner can scope and judge the work; it is not a substitute for a competent assessment.

Owners who need hazard studies, thermal data or a pre-startup review can start from our process safety and thermal hazard assessment service. It covers HAZOP and HAZID studies, LOPA and SIL review, relief and venting design, hazardous area classification and pre-startup safety review. Where the studies sit in a delivery schedule, see our EPC and EPCM project management service. The checklist above is the brief to bring to that conversation.

Frequently Asked Questions

What does a process safety consultant do?

A process safety consultant helps an owner identify, evaluate and control the hazards of a chemical process. Typical process safety consulting work includes facilitating hazard studies, measuring thermal hazard data, reviewing safeguards, supporting audits and checking a plant before start-up.

The consultant supplies method and data, and the owner keeps the legal duty and closes the actions.

When should a company hire a process safety consultant?

Hire one when a trigger arrives that the in-house team cannot meet alone: a new process, a scale-up, a change, an incident or a review date. Hire one also when the team lacks a member who knows the study method, or when the review must be independent of the design.

If the team has a trained leader, current drawings and measured data, a study can be run in-house.

Does OSHA require a process safety consultant?

The paragraphs of OSHA 29 CFR 1910.119 on process hazard analysis, incident investigation and compliance audits do not require an outside consultant. The standard places each duty on the employer and asks for knowledge in the team, such as a member who knows the method.

Under EPA 40 CFR 68.79(f), the next compliance audit must be a third-party audit in set cases, such as a qualifying release, and that provision is under review.

How do I choose a process safety consultant?

Choose on the named people, not on the firm. Ask who will lead each session, which method they will use, how independent they are from the design and where measured data will come from.

Compare the written answers across candidates, and ask for a sample worksheet and the action register format.

What qualifications should a process safety consultant have?

No single credential settles the question. One example is the CCPS Process Safety Professional Certification, which AIChE describes as verifying competency through an experience review and an examination.

HSE's guidance adds that competent includes adequate experience, so ask for the experience of the named people on similar processes.

How much does a process safety consultant cost?

Cost depends on scope, so no figure is given here. The main drivers are the number of drawings or nodes, the session days, the condition of the drawings and data, the measured data required and the depth of reporting.

State these drivers in the request so that quotations can be compared.

What is the difference between a process safety consultant and a process safety engineer?

In this guide a process safety consultant is an outside specialist engaged for a defined scope, and a process safety engineer is the in-house alternative on the payroll. Both can lead studies if they know the method.

The practical differences are independence from the design, availability and access to measured data.

Do I need an independent third-party audit?

Under EPA 40 CFR 68.79(f) as currently codified, the next RMP compliance audit must be a third-party audit in set cases. They include an accidental release meeting the criteria of section 68.42(a) and a requirement by an implementing agency. OSHA 1910.119(o) asks for an audit by at least one person knowledgeable in the process and does not say the person must be independent.

EPA proposed in February 2026 to rescind or narrow the third-party audit provisions, so check the current text.

Can a consultant take over the legal responsibility for process safety?

No. The OSHA standard places each duty on the employer, and the EPA rule places its duties on the owner or operator. A consultant can lead studies, supply data and prepare reports.

The owner still resolves the findings and certifies the compliance audits.

Need Process Safety Support Scoped Properly?

Tell us about the chemistry and the scale. Global Formulation outlines the thermal data and safety studies needed, from HAZOP and HAZID studies to pre-startup safety review.

Discuss a Safety Assessment
AK

Absar Khan

Founder & Lead Consultant, Global Formulation

Absar Khan is a senior industrial consultant with cross-disciplinary expertise spanning chemical process engineering, reaction engineering, and industrial formulation. He founded Global Formulation to provide accessible, expert-led process development and scale-up services to manufacturers and entrepreneurs in the chemical industry. Connect with him on LinkedIn.

Message on WhatsApp